|
|
 |
Home | Enerfoil Magnum Underfloor Heating
|
Magnum Millicable is a mains voltage loose cable system designed for small awkward shaped areas on existing concrete or prepared timber floors with a tile, stone, marble or slate floor finish.
|
|
|
|
|
MAGNUM enerMat is made up of an open nylon mat with integral conductor and resistance cable. It is designed for use on a concrete floor, although you can adapt a wooden floor using either tile backer boards or a thin screed of flexible tile adhesive. The total thickness of the mat, including the heating cable is only 3.5mm.
Lifetime Guarantee *
For use under tiles, stone, marble and slate etc
150 watts per m²
100% Maintenance Free
Waterproof
High tensile stengh cable
Only 3.5mm thick
Accurate wattage per m²
Primary or comfort heating **
Sizes range from 1m² to 10m² ***
No Electro Magnetic Field
Used in conjunction with the Magnum intelligent-Control Digital Clock Thermostat
NOTE: The mat can not be laid underneath any fixed units, the floor must always be able to radiate heat. Never cut or shorten the cable.
* Terms and conditions apply
** A heat loss calculation is recommended
**THERMOSTAT NOT INCLUDED PLEASE SEE SEPARATE PRODUCT Magnum MIC Control and Floor Sensor**
|
|
|
|
Most existing systems suitable for timber flooring require to be installed in a cement screed however Magnum Microfoil heating system can be placed directly underneath wooden, parquet or laminate floors. This very thin floor heating system (only 0.3 mm!) is controlled by a digital clock-thermostat with floor sensor, which ensures an equal heat distribution throughout the floor.
The floor temperature will be limited to a recommended maximum temperature of 28ΊC.
Magnum Microfoil should be placed on 6mm thin polystyrene insulation plates, these insulation plates not only increase the thermal value of the floor but also reduce noise.
Magnum Microfoil is simple to install, can be cut to size and ensures a comfortable warm environment when using a timber floor.
10 year Guarantee
Directly under wooden, laminate or parquet flooring (floating floors only)
Must be used in conjunction with the MIC thermostat and floor sensor (temperature limited) in combination with 6mm polystyrene insulation plates and 0.2 mm moisture barrier.
Can be cut to the required length every 20 cm
For use in Dry areas only
MAGNUM Microfoil is delivered as a set:
MAGNUM Microfoil on the roll from 5m², 10m² till 15m²
Sensor in flexible sensor tube.
Insulation tape
Connection crimps
Connection cables
Clearly explained manual guide
Free crimp tool
0.2mm moisture barrier
*** If you require larger sizes please call us for advice and pricing ***
|
|
|
|
MAGNUM enerCable is an ideal invisible heat source designed to go into a sand cement screed.
MAGNUM enerCable is a 7mm thick cable which comprises of conductor and resistance wires which are insulated with XLPE, a ground wire is encased in PVC and is 100% waterproof. Te high tensile strength cable heating is quickly and simply installed in screed for new builds or renovation projects.
By using spacer strips or steel mesh reinforcing grid, the cable can be installed with complete accuracy for individual output requirements the minimum installation thickness of the screed is 30mm excluding tiles or floor finish or 65mm when being laid directly onto insulation.
Lifetime Guarantee *
For new builds sand/cement screed
Economical to purchase
Simple to install
100% maintanence Free
Waterproof
No Electro Magnectic Field
A variety of floor finishes can be laid on top of enerCable**
Output wattage 100W-300W per m² depending on cable spacing
Can be used as primary or comfort heating***
Used in conjunction with the Magnum Thermostats
NOTE: The cable must not be laid under fixed units. Never cut or shorten the Cable.
*Terms and conditions apply
**Some restrictions apply
***A heat loss calculation is recommended
**THERMOSTAT NOT INCLUDED PLEASE SEE SEPARATE PRODUCT Magnum MIC Control and Floor Sensor**
|
|
|
|
|
|
|
Magnum enerFOIL is a low voltage electric underfloor warming system which is ideal for smaller areas such as bathrooms and utility rooms and can be laid directly beneath tiles, stone marble and slate.
The MAGNUM enerFoil low voltage system has been designed to operate at low voltage (24v/28v) ideal for bathrooms and wetrooms (must be waterproofed if in a wet room) and is only 80 watts or 110 watts per m², it is economical to run.
The system is designed to run 24 hours a day to maintain the temperature of the flooring material by generating an even constant heat. The actual temperature maintained will vary according to the ambient temperature, floor covering and the selected voltage and can be simply be switched off when not required.
Simple to install
Maintenance Free
Only 0.2mm thick no raising of floor levels
80 watts per m² at 24 volts or 110 watts per m² at 28 volts
100% safe low voltage through low voltage transformer
Can be installed directly onto wood or concrete ( must be smooth and flat)
Must be used with the Magnum transformer and fixed down with Magnum bond
The foils are available in widths of 300m, 400mm and 600mm in lengths up to 4.0m. Different configurations can be used to get the best possible floor coverage.
(Transformer, shown in the picture is not included)
|
|
|
|
Magnum enerFOIL is a low voltage electric underfloor warming system which is ideal for smaller areas such as bathrooms and utility rooms and can be laid directly beneath tiles, stone marble and slate.
The MAGNUM enerFoil low voltage system has been designed to operate at low voltage (24v/28v) ideal for bathrooms and wetrooms (must be waterproofed if in a wet room) and is only 80 watts or 110 watts per m², it is economical to run.
The system is designed to run 24 hours a day to maintain the temperature of the flooring material by generating an even constant heat. The actual temperature maintained will vary according to the ambient temperature, floor covering and the selected voltage and can be simply be switched off when not required.
Simple to install
Maintenance Free
Only 0.2mm thick no raising of floor levels
80 watts per m² at 24 volts or 110 watts per m² at 28 volts
100% safe low voltage through low voltage transformer
Can be installed directly onto wood or concrete ( must be smooth and flat)
Must be used with the Magnum transformer and fixed down with Magnum bond
The foils are available in widths of 300m, 400mm and 600mm in lengths up to 4.0m. Different configurations can be used to get the best possible floor coverage.
(Transformer, shown in the picture is not included)
|
|
|
|
A low voltage AC current, supplied via a transformer powers the heating panels.
The size of transformer is determined by the number of panels used in the installation.
A low voltage AC current, supplied via a transformer powers the heating panels.
The size of transformer is determined by the number of panels used in the installation.
To work out the size of transformer required simply add up the amount of heating segments used and choose the relevant transformer suitable for your total heating segements.
|
|
|
|
Home | Enerfoil Magnum Underfloor Heating
|
|
|
|
|
|
